Thermal Barrier Coatings (TBC) For Carbon Fiber-Reinforced Polymer (CFRP) Composites: A Review
DOI:
https://doi.org/10.59585/ijhs.v4i4.2039Keywords:
thermal barrier coating, CFRP, thermal conductivity, thermal shock, porosityAbstract
Carbon fiber-reinforced polymer (CFRP) composites are widely used in high-performance lightweight structures, yet their thermoset matrices begin to decompose at about 300°C, which limits their use in high-temperature environments. This article presents a comparative narrative review of two studies on thermal barrier coatings (TBCs) for CFRP developed by the same research group. The first study used a compression-molded Al2O3 plate mechanically bonded to CFRP through vacuum-assisted resin transfer molding (VARTM), whereas the second used a double-layered yttria-stabilized zirconia (YSZ) TBC with graded porosity produced by flame spraying with PEEK particles as a pore former. Fabrication parameters, microstructure, thermal conductivity, thermal shock response, and residual flexural performance were extracted from both studies and compared. In the first study, a 1.45 mm TBC reduced the back-surface temperature of CFRP to 188–228°C under 500–700°C flames while retaining 90%, 62%, and 50% of the failure load, whereas uncoated CFRP lost 93–95% at 600–700°C. In the second study, a TBC about 0.66 mm thick with a thermal conductivity of about 0.3 W/m·K held the back surface at 230°C for 10 minutes under a 500°C flame, retaining 87% of flexural strength and 75% of modulus, while uncoated CFRP ignited. Both approaches are effective but rely on different protection mechanisms. Non-uniform test protocols, the absence of areal mass data, and the lack of long-term cyclic testing are the main limitations to be addressed in future work
Downloads
References
Ahmadi, M. S., Shoja-Razavi, R., Valefi, Z. and Jamali, H. (2019) ‘The effect of laser surface treatment on the thermal shock behavior of plasma sprayed Al2O3/YSZ multilayer thermal barrier coatings’, Surface and Coatings Technology, 366, pp. 62–69. doi: 10.1016/j.surfcoat.2019.03.024.
Alkurdi, A. A. et al. (2024) ‘Enhancing mechanical behavior assessment in porous thermal barrier coatings using a machine learning fine-tuned with genetic algorithm’, Journal of Thermal Spray Technology, 33(4), pp. 824–838. doi: 10.1007/s11666-024-01756-w.
Altaf, S. F., Rahman, A. and Wani, M. (2025) ‘Long-term stability and performance of nanostructured thermal barrier coatings deposited by magnetron sputtering on superalloys: a review’, Surface Engineering, 41(2), pp. 149–175. doi: 10.1177/02670844251328622.
Ando, H., Ambe, Y., Ishii, A., Konyo, M., Tadakuma, K., Maruyama, S. and Tadokoro, S. (2018) ‘Aerial hose type robot by water jet for fire fighting’, IEEE Robotics and Automation Letters, 3(2), pp. 1128–1135. doi: 10.1109/LRA.2018.2792701.
Ariyanayagam, A. D. and Mahendran, M. (2014) ‘Development of realistic design fire time–temperature curves for the testing of cold-formed steel wall systems’, Frontiers of Structural and Civil Engineering, 8(4), pp. 427–447. doi: 10.1007/s11709-014-0279-1.
Bard, S., Schönl, F., Demleitner, M. and Altstädt, V. (2019) ‘Influence of fiber volume content on thermal conductivity in transverse and fiber direction of carbon fiber-reinforced epoxy laminates’, Materials, 12(7), p. 1084. doi: 10.3390/ma12071084.
Bellippady, M. et al. (2024) ‘Performance of atmospheric plasma-sprayed thermal barrier coatings on additively manufactured super alloy substrates’, Coatings, 14(5), p. 626. doi: 10.3390/coatings14050626.
Chen, D. and Dambra, C. (2024) ‘Thick columnar-structured thermal barrier coatings using the suspension plasma spray process’, Coatings, 14(8), p. 996. doi: 10.3390/coatings14080996.
Chen, X., Zhao, Y., Fan, X., Liu, Y., Zou, B., Wang, Y. et al. (2011) ‘Thermal cycling failure of new LaMgAl11O19/YSZ double ceramic top coat thermal barrier coating systems’, Surface and Coatings Technology, 205(10), pp. 3293–3300. doi: 10.1016/j.surfcoat.2010.11.059.
Cilento, F., Leone, C., Genna, S., Giordano, M. and Martone, A. (2023) ‘Graphene NanoPlatelet-based coating as thermal protection from high-power radiative fluxes’, Composite Structures, 319, p. 117157.
Clarke, D. and Levi, C. (2003) ‘Materials design for the next generation thermal barrier coatings’, Annual Review of Materials Research, 33(1), pp. 383–417. doi: 10.1146/annurev.matsci.33.011403.113718.
Clarke, D. R. and Phillpot, S. R. (2005) ‘Thermal barrier coating materials’, Materials Today, 8(6), pp. 22–29. doi: 10.1016/S1369-7021(05)70934-2.
Craig, M. et al. (2015) ‘CMAS degradation of EB-PVD TBCs: the effect of basicity’, Surface and Coatings Technology, 270, pp. 145–153. doi: 10.1016/j.surfcoat.2015.03.009.
Dai, S. et al. (2024) ‘Cold spray technology and its application in the manufacturing of metal matrix composite materials with carbon-based reinforcements’, Coatings, 14(7), p. 822. doi: 10.3390/coatings14070822.
Dennison, P. E., Charoensiri, K., Roberts, D. A., Peterson, S. H. and Green, R. O. (2006) ‘Wildfire temperature and land cover modeling using hyperspectral data’, Remote Sensing of Environment, 100(2), pp. 212–222. doi: 10.1016/j.rse.2005.10.007.
Dong, C., Li, K., Jiang, Y., Arola, D. and Zhang, D. (2018) ‘Evaluation of thermal expansion coefficient of carbon fiber reinforced composites using electronic speckle interferometry’, Optics Express, 26(1), pp. 531–543. doi: 10.1364/OE.26.000531.
Evans, A. G. et al. (2001) ‘Mechanisms controlling the durability of thermal barrier coatings’, Progress in Materials Science, 46(5), pp. 505–553. doi: 10.1016/S0079-6425(00)00020-7.
Fan, W. and Bai, Y. (2016) ‘Review of suspension and solution precursor plasma sprayed thermal barrier coatings’, Ceramics International, 42(13), pp. 14299–14312. doi: 10.1016/j.ceramint.2016.06.063.
Fang, Z., Li, M., Wang, S., Gu, Y., Li, Y. and Zhang, Z. (2019) ‘Through-thickness thermal conductivity enhancement of carbon fiber composite laminate by filler network’, International Journal of Heat and Mass Transfer, 137, pp. 1103–1111. doi: 10.1016/j.ijheatmasstransfer.2019.04.007.
Feuerstein, A., Knapp, J., Taylor, T., Ashary, A., Bolcavage, A. and Hitchman, N. (2008) ‘Technical and economical aspects of current thermal barrier coating systems for gas turbine engines by thermal spray and EBPVD: a review’, Journal of Thermal Spray Technology, 17(2), pp. 199–213. doi: 10.1007/s11666-007-9148-y.
Golewski, P. and Sadowski, T. (2018) ‘A novel application of alumina fiber mats as TBC protection for CFRP/epoxy laminates – laboratory tests and numerical modeling’, Journal of the European Ceramic Society, 38(8), pp. 2920–2927. doi: 10.1016/j.jeurceramsoc.2018.01.008.
Golewski, P. and Sadowski, T. (2019) ‘Description of thermal protection against heat transfer of carbon fiber reinforced plastics (CFRP) coated by stiffened ceramic mat (TBC)’, Composite Structures, 229, p. 111489. doi: 10.1016/j.compstruct.2019.111489.
Guo, D. et al. (2022) ‘Cold spray: over 30 years of development toward a hot future’, Journal of Thermal Spray Technology, 31(4), pp. 866–907. doi: 10.1007/s11666-022-01366-4.
He, Y.-L. and Xie, T. (2015) ‘Advances of thermal conductivity models of nanoscale silica aerogel insulation material’, Applied Thermal Engineering, 81, pp. 28–50. doi: 10.1016/j.applthermaleng.2015.02.013.
Hirata, Y., Itoh, S., Shimonosono, T. and Sameshima, S. (2016) ‘Theoretical and experimental analyses of Young’s modulus and thermal expansion coefficient of the alumina–mullite system’, Ceramics International, 42(15), pp. 17067–17073. doi: 10.1016/j.ceramint.2016.07.216.
Hutchinson, J. W. and Evans, A. G. (2002) ‘On the delamination of thermal barrier coatings in a thermal gradient’, Surface and Coatings Technology, 149(2–3), pp. 179–184. doi: 10.1016/S0257-8972(01)01451-7.
Jarrah, M., Najafabadi, E. P., Khaneghahi, M. H. and Oskouei, A. V. (2018) ‘The effect of elevated temperatures on the tensile performance of GFRP and CFRP sheets’, Construction and Building Materials, 190, pp. 38–52. doi: 10.1016/j.conbuildmat.2018.09.086.
Ju, L., Yang, J., Hao, A., Daniel, J., Morales, J., Nguyen, S. et al. (2018) ‘A hybrid ceramic-polymer composite fabricated by co-curing lay-up process for a strong bonding and enhanced transient thermal protection’, Ceramics International, 44(10), pp. 11497–11504. doi: 10.1016/j.ceramint.2018.03.211.
Kandare, E., Khatibi, A. A., Yoo, S., Wang, R., Ma, J., Olivier, P. et al. (2015) ‘Improving the through-thickness thermal and electrical conductivity of carbon fibre/epoxy laminates by exploiting synergy between graphene and silver nano-inclusions’, Composites Part A: Applied Science and Manufacturing, 69, pp. 72–82. doi: 10.1016/j.compositesa.2014.10.024.
Khaneghahi, M. H., Najafabadi, E. P., Shoaei, P. and Oskouei, A. V. (2018) ‘Effect of intumescent paint coating on mechanical properties of FRP bars at elevated temperature’, Polymer Testing, 71, pp. 72–86. doi: 10.1016/j.polymertesting.2018.08.020.
Kim, H., Kim, J., Lee, J. and Lee, M. W. (2021) ‘Thermal barrier coating for carbon fiber-reinforced composite materials’, Composites Part B: Engineering, 225, p. 109308. doi: 10.1016/j.compositesb.2021.109308.
Kim, H., Praveen, K., Lee, M. W. and Lee, J. (2024) ‘Performance-tunable thermal barrier coating for carbon fiber-reinforced plastic composites via flame spraying’, Composites Part B: Engineering, 287, p. 111842. doi: 10.1016/j.compositesb.2024.111842.
Kim, Y., Ryu, K.-H., Na, W., Yu, J. and Lee, M. W. (2020) ‘Origami-inspired reforming method for carbon fiber-reinforced thermoplastics via simple thermal stitching’, Composites Part B: Engineering, 193, p. 108043. doi: 10.1016/j.compositesb.2020.108043.
Kodur, V. K. R., Bhatt, P. P. and Naser, M. Z. (2019) ‘High temperature properties of fiber reinforced polymers and fire insulation for fire resistance modeling of strengthened concrete structures’, Composites Part B: Engineering, 175, p. 107104. doi: 10.1016/j.compositesb.2019.107104.
Könnicke, D., Kühn, A., Mahrholz, T. and Sinapius, M. (2011) ‘Polymer nanocomposites based on epoxy resin and ATH as a new flame retardant for CFRP: preparation and thermal characterisation’, Journal of Materials Science, 46(21), pp. 7046–7055. doi: 10.1007/s10853-011-5673-7.
Krishnaswamy, S., Abhyankar, H., Marchante, V., Huang, Z. and Brighton, J. (2019) ‘Aerogel/epoxy thermal coatings for carbon fibre reinforced plastic substrates’, Journal of Adhesion Science and Technology, 33(6), pp. 579–594.
Lee, K. N., Fox, D. S., Eldridge, J. I., Zhu, D., Robinson, R. C., Bansal, N. P. and Miller, R. A. (2003) ‘Upper temperature limit of environmental barrier coatings based on mullite and BSAS’, Journal of the American Ceramic Society, 86(8), pp. 1299–1306. doi: 10.1111/j.1151-2916.2003.tb03466.x.
Leng, K., Romero, A. R. and Hussain, T. (2023) ‘Multilayer GZ/YSZ thermal barrier coating from suspension and solution precursor thermal spray’, Journal of the European Ceramic Society, 43(11), pp. 4991–5003. doi: 10.1016/j.jeurceramsoc.2023.04.014.
Liu, B., Liu, Y., Zhu, C., Xiang, H., Chen, H., Sun, L. et al. (2019) ‘Advances on strategies for searching for next generation thermal barrier coating materials’, Journal of Materials Science & Technology, 35(5), pp. 833–851. doi: 10.1016/j.jmst.2018.11.016.
Liu, L. et al. (2024) ‘Failure of electron beam physical vapor deposited thermal barrier coatings system under cyclic thermo-mechanical loading with a thermal gradient’, Coatings, 14(7), p. 902. doi: 10.3390/coatings14070902.
Luangtriratana, P., Kandola, B. K. and Myler, P. (2015) ‘Ceramic particulate thermal barrier surface coatings for glass fibre-reinforced epoxy composites’, Materials & Design, 68, pp. 232–244. doi: 10.1016/j.matdes.2014.11.057.
Mehta, A. et al. (2022) ‘Processing and advancements in the development of thermal barrier coatings: a review’, Coatings, 12(9), p. 1318. doi: 10.3390/coatings12091318.
Mittal, G. and Paul, S. (2022) ‘Suspension and solution precursor plasma and HVOF spray: a review’, Journal of Thermal Spray Technology, 31(5), pp. 1443–1475. doi: 10.1007/s11666-022-01360-w.
Moridi, A., Azadi, M. and Farrahi, G. H. (2014) ‘Thermo-mechanical stress analysis of thermal barrier coating system considering thickness and roughness effects’, Surface and Coatings Technology, 243, pp. 91–99. doi: 10.1016/j.surfcoat.2012.02.019.
Morvan, D. and Dupuy, J.-L. (2004) ‘Modeling the propagation of a wildfire through a Mediterranean shrub using a multiphase formulation’, Combustion and Flame, 138(3), pp. 199–210. doi: 10.1016/j.combustflame.2004.05.001.
Nguyen, P. L., Vu, X. H. and Ferrier, E. (2019) ‘Thermo-mechanical performance of carbon fiber reinforced polymer (CFRP), with and without fire protection material, under combined elevated temperature and mechanical loading conditions’, Composites Part B: Engineering, 169, pp. 164–173. doi: 10.1016/j.compositesb.2019.03.075.
Nieto, A. et al. (2021) ‘Calcia–magnesia–alumina–silicate (CMAS) attack mechanisms and roadmap towards sandphobic thermal and environmental barrier coatings’, International Materials Reviews, 66(7), pp. 451–492. doi: 10.1080/09506608.2020.1824414.
Padture, N. P., Gell, M. and Jordan, E. H. (2002) ‘Thermal barrier coatings for gas-turbine engine applications’, Science, 296(5566), pp. 280–284. doi: 10.1126/science.1068609.
Peng, H. et al. (2012) ‘Degradation of EB-PVD thermal barrier coatings caused by CMAS deposits’, Progress in Natural Science: Materials International, 22(5), pp. 461–467. doi: 10.1016/j.pnsc.2012.06.007.
Praveen, K., Kim, H., Lee, J., Cha, J.-H. and Lee, M. W. (2026) ‘High-performance ceramic thermal barrier coatings for carbon fiber-reinforced plastics developed by atmospheric plasma spraying’, Composites Part A: Applied Science and Manufacturing, 201, p. 109424. doi: 10.1016/j.compositesa.2025.109424.
Restas, A. (2015) ‘Drone applications for supporting disaster management’, World Journal of Engineering and Technology, 3(3), pp. 316–321. doi: 10.4236/wjet.2015.33C047.
Soleimanipour, Z., Baghshahi, S., Shoja-Razavi, R. and Salehi, M. (2016) ‘Hot corrosion behavior of Al2O3 laser clad plasma sprayed YSZ thermal barrier coatings’, Ceramics International, 42(15), pp. 17698–17705. doi: 10.1016/j.ceramint.2016.08.090.
Tejero-Martin, D. et al. (2019) ‘Beyond traditional coatings: a review on thermal-sprayed functional and smart coatings’, Journal of Thermal Spray Technology, 28, pp. 598–644. doi: 10.1007/s11666-019-00857-1.
Tian, T. and Cole, K. D. (2012) ‘Anisotropic thermal conductivity measurement of carbon-fiber/epoxy composite materials’, International Journal of Heat and Mass Transfer, 55(23–24), pp. 6530–6537. doi: 10.1016/j.ijheatmasstransfer.2012.06.059.
Vaßen, R. et al. (2010) ‘Overview on advanced thermal barrier coatings’, Surface and Coatings Technology, 205(4), pp. 938–942. doi: 10.1016/j.surfcoat.2010.08.151.
Wang, L. et al. (2022) ‘Effects of TGO growth on the stress distribution and evolution of three-dimensional cylindrical thermal barrier coatings based on finite element simulations’, Ceramics International, 48(6), pp. 7864–7875. doi: 10.1016/j.ceramint.2021.11.334.
Xie, L. et al. (2004) ‘Processing parameter effects on solution precursor plasma spray process spray patterns’, Surface and Coatings Technology, 183(1), pp. 51–61. doi: 10.1016/j.surfcoat.2003.09.071.
Yao, Y., Yang, F. and Zhao, X. (2022) ‘Multicomponent high-entropy Zr-Y-Yb-Ta-Nb-O oxides for next-generation thermal barrier coating applications’, Journal of the American Ceramic Society, 105(1), pp. 35–43. doi: 10.1111/jace.18053.
Ye, D. et al. (2024) ‘Terahertz non-destructive testing of porosity in multi-layer thermal barrier coatings based on small-sample data’, Coatings, 14(11), p. 1357. doi: 10.3390/coatings14111357.
Yu, G.-C., Wu, L.-Z. and Feng, L.-J. (2015) ‘Enhancing the thermal conductivity of carbon fiber reinforced polymer composite laminates by coating highly oriented graphite films’, Materials & Design, 88, pp. 1063–1070. doi: 10.1016/j.matdes.2015.09.096.
Zhao, D. et al. (2024) ‘Melt-grown behaviour of heat treated high-purity alumina ceramics prepared by laser directed energy deposition’, Ceramics International, 50(1), pp. 1777–1787. doi: 10.1016/j.ceramint.2023.10.277.
Zhao, D. et al. (2025) ‘Thermal properties for Al2O3-based melt-grown ceramics prepared by laser-directed energy deposition’, Journal of Alloys and Compounds, 1010, p. 177795. doi: 10.1016/j.jallcom.2024.177795.
Zhou, D. et al. (2024) ‘Microstructure and thermal shock behavior of CoMoCrSi coatings prepared by HVOF and APS’, Surface and Coatings Technology, 478, p. 130498. doi: 10.1016/j.surfcoat.2024.130498.
Zhu, D. and Miller, R. A. (2000) ‘Thermal-barrier coatings for advanced gas-turbine engines’, MRS Bulletin, 25(7), pp. 43–47. doi: 10.1557/mrs2000.123.
Zhu, H. et al. (2023) ‘Prediction of microstructure and mechanical properties of atmospheric plasma-sprayed 8YSZ thermal barrier coatings using hybrid machine learning approaches’, Coatings, 13(3), p. 602. doi: 10.3390/coatings13030602.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 Fesa Mahardika Anastasya, Sovian Aritonang, Hotma Renta R Siringoringo, Richard Panjaitan, Cindy Florecita, Luthfiah Maharani

This work is licensed under a Creative Commons Attribution 4.0 International License.

International Journal of Health Sciences is licensed under a Creative Commons Attribution 4.0 International License


