Yield Strength And Fracture Toughness Of High-Strength Steels For Deep-Sea Submarine Pressure Hulls: A Systematic Review

Authors

  • Richard Panjaitan Indonesia Defense University, Indonesia
  • Sovian Aritonang Indonesia Defense University, Indonesia
  • Hotma Renta Indonesia Defense University, Indonesia
  • Fesa Mahardika Indonesia Defense University, Indonesia
  • Afriza Rizky Indonesia Defense University, Indonesia
  • Rivandio Sitanggang Indonesia Defense University, Indonesia

DOI:

https://doi.org/10.59585/ijhs.v4i4.2018

Keywords:

High-strength Steel, Submarine pressure hull, Yield strength, Fracture toughness, Johnson–Cook

Abstract

The pressure hull of a deep-sea submarine requires steel that is strong and also tough at low temperature. This article aims to synthesise the relationship between yield strength and fracture toughness of high-strength steels for deep-sea submarine pressure hulls. A qualitative narrative synthesis based on document analysis was applied to two selected sources: a review of the strengthening and toughening mechanisms of HSLA, Co–Ni secondary hardening and maraging steels, and an experimental study of HY-80 steel from the hull of a Kobben-class submarine after about 55 years of operation. Key figures were extracted from both sources and recalculated where possible. The results show that high strength mainly originates from high-density dislocations, nanoprecipitates and intermetallic compounds, whereas toughness is improved by martensite refinement, metastable austenite, coherent precipitates with low lattice misfit and inclusion control. The aged HY-80 steel had an average yield point of 605.6 MPa, about 9.7% above the catalogue value of 552 MPa, and a true ultimate strength of 782 MPa that rose to 1140 MPa at a strain rate of 2159 s⁻¹. Johnson–Cook and failure parameters (d = 0.414; εf = 0.1289) are available for finite element simulation, but the values of n and B and the mean of C should be re-verified. It is concluded that the proposed synergy of low-misfit precipitates and reversed austenite in a high-density dislocation martensitic matrix is promising, but the toughness of the aged hull steel has not been measured directly, so impact and K1C testing are still required

Downloads

Download data is not yet available.

References

Baker, T.N. (2009) ‘Processes, microstructure and properties of vanadium microalloyed steels’, Materials Science and Technology, 25, pp. 1083–1107. doi: 10.1179/174328409X453253.

Floreen, S. (1968) ‘The physical metallurgy of maraging steels’, Metallurgical Reviews, 13, pp. 115–128. doi: 10.1179/mtlr.1968.13.1.115.

Garrison, W.M. and Maloney, J.L. (2005) ‘Lanthanum additions and the toughness of ultra-high strength steels and the determination of appropriate lanthanum additions’, Materials Science and Engineering: A, 403, pp. 299–310. doi: 10.1016/j.msea.2005.05.021.

Han, J., Wang, K., Wang, Z. and Yu, H. (2024) ‘Tailoring the strength and low-temperature toughness of HSLA structural steel by adding trace Ce’, Materials Today Communications, 40, 109789. doi: 10.1016/j.mtcomm.2024.109789.

Holmquist, T.J. (1987) Strength and fracture characteristics of HY-80, HY-100, and HY-130 steels subjected to various strains, strain rates, temperatures, and pressures. Dahlgren, VA: Naval Surface Warfare Center.

Jiang, S.H., Wang, H., Wu, Y., Liu, X.J., Chen, H.H., Yao, M.J., Gault, B., Ponge, D., Raabe, D., Hirata, A., Chen, M.W., Wang, Y.D. and Lu, Z.P. (2017) ‘Ultrastrong steel via minimal lattice misfit and high-density nanoprecipitation’, Nature, 544, pp. 460–464. doi: 10.1038/nature22032.

Kan, L.Y., Ye, Q.B., Shen, Y.F., Wang, Z.D. and Zhao, T. (2022a) ‘Co-precipitation of nanosized Cu and carbides improving mechanical properties of 1 GPa grade HSLA steel’, Materials Science and Engineering: A, 859, 144211. doi: 10.1016/j.msea.2022.144211.

Kan, L., Ye, Q., Wang, Z. and Zhao, T. (2022b) ‘Improvement of strength and toughness of 1 GPa Cu-bearing HSLA steel by direct quenching’, Materials Science and Engineering: A, 855, 143875. doi: 10.1016/j.msea.2022.143875.

Kuzmina, M., Ponge, D. and Raabe, D. (2015) ‘Grain boundary segregation engineering and austenite reversion turn embrittlement into toughness: example of a 9 wt% medium Mn steel’, Acta Materialia, 86, pp. 182–192. doi: 10.1016/j.actamat.2014.12.021.

Lacroix, G., Pardoen, T. and Jacques, P.J. (2008) ‘The fracture toughness of TRIP-assisted multiphase steels’, Acta Materialia, 56, pp. 3900–3913. doi: 10.1016/j.actamat.2008.04.035.

Li, J., Zhan, D., Jiang, Z., Zhang, H., Yang, Y. and Zhang, Y. (2023) ‘Progress on improving strength-toughness of ultra-high strength martensitic steels for aerospace applications: a review’, Journal of Materials Research and Technology, 23, pp. 172–190. doi: 10.1016/j.jmrt.2022.12.177.

Liu, L., Yu, Q., Wang, Z., Ell, J., Huang, M.X. and Ritchie, R.O. (2020) ‘Making ultrastrong steel tough by grain-boundary delamination’, Science, 368, pp. 1347–1352. doi: 10.1126/science.aba9413.

Meng, X.Y., Wu, S.D. and Wang, Z.H. (2014) ‘Development and prospects of material technology of steel using in submarine hull’, Ship Science and Technology, 36, pp. 1–5.

Mondiere, A., Déneux, V., Binot, N. and Delagnes, D. (2018) ‘Controlling the MC and M2C carbide precipitation in Ferrium® M54® steel to achieve optimum ultimate tensile strength/fracture toughness balance’, Materials Characterization, 140, pp. 103–112. doi: 10.1016/j.matchar.2018.03.041.

Niu, M., Zhou, G., Wang, W., Shahzad, M.B., Shan, Y. and Yang, K. (2019) ‘Precipitate evolution and strengthening behavior during aging process in a 2.5 GPa grade maraging steel’, Acta Materialia, 179, pp. 296–307. doi: 10.1016/j.actamat.2019.08.042.

Sun, L., Simm, T.H., Martin, T.L., McAdam, S., Galvin, D.R., Perkins, K.M., Bagot, P.A. et al. (2018) ‘A novel ultra-high strength maraging steel with balanced ductility and creep resistance achieved by nanoscale β-NiAl and Laves phase precipitates’, Acta Materialia, 149, pp. 285–301. doi: 10.1016/j.actamat.2018.02.044.

Szturomski, B. and Kiciński, R. (2021) ‘Material properties of HY 80 steel after 55 years of operation for FEM applications’, Materials, 14(15), 4213. doi: 10.3390/ma14154213.

Wang, B., Zhang, H., Mi, P., Zhang, G., Hao, L., Xu, B., Sun, M. and Li, D. (2024a) ‘Revealing the evolution behavior of multiple carbides precipitation and mechanical response in M54 secondary hardening steel’, Materials Characterization, 211, 113856. doi: 10.1016/j.matchar.2024.113856.

Wang, C., Wang, M., Shi, J., Hui, W. and Dong, H. (2008) ‘Effect of microstructural refinement on the toughness of low carbon martensitic steel’, Scripta Materialia, 58, pp. 492–495. doi: 10.1016/j.scriptamat.2007.10.053.

Wang, L., Ye, C., Sun, C., Feng, S., Xie, X., Gao, Y., Zhao, K., Li, Y. and Wan, Z. (2024b) ‘Experimental investigation on compressive dwell fatigue behavior of titanium alloy pressure hull for deep-sea manned submersibles’, Ocean Engineering, 303, 117646. doi: 10.1016/j.oceaneng.2024.117646.

Wang, S., Gao, Z., Wu, G. and Mao, X. (2022) ‘Titanium microalloying of steel: a review of its effects on processing, microstructure and mechanical properties’, International Journal of Minerals, Metallurgy and Materials, 29, pp. 645–661. doi: 10.1007/s12613-021-2399-7.

Wang, S., Jin, Y., Li, Y., Zhao, T., Deng, X. and Wang, Z. (2025) ‘Review: strengthening and toughening mechanisms of high-strength steels for deep-sea pressure vessel hulls’, Journal of Materials Science, 60, pp. 15387–15420. doi: 10.1007/s10853-025-11354-y.

Wang, Z.H., Niu, B., Wang, Q., Dong, C., Jie, J.C., Wang, T.M. and Nieh, T.G. (2021) ‘Designing ultrastrong maraging stainless steels with improved uniform plastic strain via controlled precipitation of coherent nanoparticles’, Journal of Materials Science & Technology, 93, pp. 60–70. doi: 10.1016/j.jmst.2021.04.011.

Wu, H., Ju, B., Tang, D., Hu, R., Guo, A., Kang, Q. and Wang, D. (2015) ‘Effect of Nb addition on the microstructure and mechanical properties of an 1800 MPa ultrahigh strength steel’, Materials Science and Engineering: A, 622, pp. 61–66. doi: 10.1016/j.msea.2014.11.005.

Zhou, C., Ye, Q., Hu, J., Zhao, T., Gao, X. and Wang, Z. (2022) ‘Ultra-high-strength multi-alloyed steel with enhanced cryogenic toughness using thermally stable retained austenite’, Materials Science and Engineering: A, 831, 142356. doi: 10.1016/j.msea.2021.142356.

Zhou, X., Jia, C., Mi, P., Zhang, H., Yan, W., Wang, W., Sun, M. and Rong, L. (2025) ‘Cyclic quenching treatment doubles the Charpy V-notch impact energy of a 2.3 GPa maraging steel’, Journal of Materials Science & Technology, 209, pp. 311–328. doi: 10.1016/j.jmst.2024.05.026.

Downloads

Published

2026-11-17

How to Cite

Panjaitan, R., Aritonang, S., Renta, H., Mahardika, F., Rizky, A., & Sitanggang, R. (2026). Yield Strength And Fracture Toughness Of High-Strength Steels For Deep-Sea Submarine Pressure Hulls: A Systematic Review. International Journal of Health Sciences, 4(4), 1356–1367. https://doi.org/10.59585/ijhs.v4i4.2018